Can I Set Up a Bathtub Myself? Factors to Consider As Well As Steps
Can I Set Up a Bathtub Myself? Factors to Consider As Well As Steps
Blog Article
The content down below relating to Installing A Bathtub is extremely intriguing. Read on and draw your own assumptions.
Installing a tub isn't specifically brain surgery, but it does need strong plumbing, carpentry, and also occasionally, tiling abilities. Replacing an old bathtub with a new one is additionally a reasonably difficult job. If the old bathtub is conveniently obtainable, the task can relocate easily; if you have to open a wall to eliminate the old bathtub and also place the new bathtub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will certainly need a helper to move out the old tub as well as set in the brand-new one. Make certain you have certified on your own for the task and are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed task, it is far better to take into consideration using one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This write-up will certainly aid you mount a brand-new bath tub in your shower room if you have actually currently bought a brand-new bathtub and also do not require to alter the plan of your previous supply of water pipes.
Your tools and material list need to make up the following:
Preparing for the Installment
First of all, the sustaining framework supplied with the bath needs to be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to see to it that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets device to avoid strain on the bath tub.
Fit the adaptable tap connectors to the bottom of both faucets using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you make use of all of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its final placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you must do is disconnect the water. After doing so, turn on the faucets to drain any kind of water remaining in the system. The process of eliminating the existing taps can be rather bothersome because of the limited gain access to that is usually the case.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a towel ready for the staying water that will certainly come from the pipelines. As soon as the supply pipes have actually been gotten rid of, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any kind of old sealing substance.
Prior to moving on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Setting up the Bath tub
Making use of the two wooden boards under its feet, put the bath tub in the required position. The wooden boards are practical in equally spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small points.
The next goal is to ensure that the tub is leveled all round. This can be accomplished by examining the level and also adjusting the feet on the bathtub up until the spirit level checks out degree.
To mount faucets, fit all-time low of the furthest flexible tap connector to the suitable supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Switch on the water and also examine all joints and new pipework for leaks and tighten them if necessary. Fill the bathtub and also check the overflow outlet and the normal electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as defined in the maker's user's manual. Tiling as well as sealing around the tub ought to wait up until the bathtub has been used at least when as this will certainly resolve it right into its last setting.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end supplies a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, position the faucet in the placing opening in the bath/basin guaranteeing that the washers remain in area in between the tap and the sink. Safeguard the faucet in place with the manufacturer given backnut. When the tap is securely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular faucet connectors. The previous kind ought to be connected to the faucet ends first, tightening up just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to break an inflexible seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, bring about issues with dampness and also possible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components as well as installations. They are offered in tubes and cartridges, as well as can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bathtub with water prior to securing, to enable the activity experienced when the tub remains in use. The sealer can fracture relatively very early if you do not consider this activity before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently offered on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like more info about A Step-by-Step Guide to Installing a Bathtub? Leave feedback directly below. We will be pleased to hear your thoughts about this blog post. Hoping that you visit us again in the near future. Liked our blog posting? Please share it. Let another person discover it. Many thanks for going through it.
Book With Us Today!
Report this page